Author: Admin

UCS 2.1 Backup

Posted on by Admin

Backup and Export Configuration When you perform a backup through Cisco UCS Manager, you take a snapshot of all or part of the system configuration and export the file to a location on your network. You cannot use Cisco UCS Manager to back up data on the servers. You can perform a backup while the system is up and running. The backup operation only saves information from the management plane. It does not have any impact on the…

Read More

Cisco BUG [ CSCea28215 ] Various MGX Modules may require reset after 466+ days – Workaround procedure available

Posted on by Admin

Field Notice: FN – 63249 MGX – A software bug CSCea28215 in VxWorks caused incorrect handling of rollover tick counter, various MGX Modules may require reset after 466+ days – Workaround procedure available   Cisco BUG and FN; – CSCea28215 466+ days Wxworks BUG – FN 63249: http://www.cisco.com/c/en/us/support/docs/field-notices/632/fn63249.html NOTICE: THIS FIELD NOTICE IS PROVIDED ON AN “AS IS” BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTY OF MERCHANTABILITY. YOUR…

Read More

Verifying the Platform State of the Cisco PGW 2200 Softswitches

Posted on by Admin

  Verifying the Platform State of the Cisco PGW 2200 Softswitches You can determine which of your Cisco PGW 2200 Softswitches is the active Cisco PGW 2200 Softswitch and which is the standby Cisco PGW 2200 Softswitch. If your system uses a Cisco PGW 2200 Softswitch in a simplex configuration, the single Cisco PGW 2200 Softswitch is always active. To do this, complete the following steps: Step 1 Log into one of the Cisco PGW 2200 Softswitches,…

Read More

Setting up SecureCRT – Change Default Appearance + Auto-create Log File On Connect

Posted on by Admin

This is just a collection of convenient settings I’ve found elsewhere on the Internet. SecureCRT is a nice little piece of software to have in sitting on your laptop to connect to console/Telnet/SSH sessions you frequent/etc. Some of the settings I’d prefer to change from the default, mainly around appearance and with it not automatically creating a log file on connect. Change Default Appearance To change the default colour theme do the following: Go to Options > Global…

Read More

How to patch ESXi 5 without vCenter by Using ESXCLi

Posted on by Admin

  How to patch ESXi 5 from command line. Usually the patching of VMware vSphere Cluster is done through vSphere Update Manager (VUM), but for this you need vCenter. In case you’re managing single ESXi host without vCenter, you might be interested to know how to patch the ESXi host from the command line.   The patching of VMware ESXi 5 is quite straightforward process, but there is one condition: SSH access The SSH access can…

Read More

Installing patches on an ESXi 5.x host from the command line

Posted on by Admin

Installing patches on an ESXi 5.x host from the command line (2008939) Purpose This article outlines the procedure for installing patches on an ESXi 5.x host from the command line using esxcli software vib commands. For more information on installing VIBs on an ESX host, see Update a Host with Individual VIBs in the vSphere 5 Documentation Center. You can also install patches using esxcli software profile commands. For more information, see vSphere Command-Line Interface…

Read More

Cisco 7609 (ROMMON Upgrade Procedure Guide)

Posted on by Admin
Cisco 7609 (ROMMON Upgrade Procedure Guide)

  Verification and backup commands before upgrade:  ! show redundancy!show rom-monitor slot 5 sp show rom-monitor slot 5 rp show rom-monitor slot 6 sp show rom-monitor slot 6 rp show tac !             First start ROMMON upgrade with standby supervisor:                 Note: standby supervisor is in module 6: Please note first upgrade the SP image on standby supervisor and verify after that you can upgrade RP         image on standby…

Read More

Transfered CAlls – CDR Reading

Posted on by Admin

CDR Reading for Transferred Calls Transferred Calls Calls that are transferred generate multiple CDRs. One CDR exists for the original call, one for the consultation call, and another for the final transferred call. For the original call, the origCause_value and destCause_value gets set to split = 393216, which indicates the call was split. The origCallTerminationOnBehalfOf and destCallTerminationOnBehalfOf fields get set to Transfer = 10 to indicate that this call was involved in a transfer. For…

Read More

Cisco PGW Basics

Posted on by Admin

  To manually start the Cisco PGW 2200 Softswitch software, log in to the active Cisco PGW 2200 Softswitch as root and enter the following command: # /etc/init.d/CiscoMGC start To manually stop the Cisco PGW 2200 Softswitch software, log into your active Cisco PGW 2200 Softswitch as root and enter the following command: # /etc/init.d/CiscoMGC stop Starting an MML Session When a procedure requires that you start an MML session, you must perform the following…

Read More
1 … 3,521 3,522 3,523 3,524 3,525 … 3,532