Author: Admin

EEM Applet and TCL scrips (Count & email )

Posted on by Admin

Below 2 email will be sent at 23:00. One will contain the contains of file RTPReport.txt and the second the contains of SIPcount.txt A snapshot of the number of rtp streams is taken every 30 minute. A counter of the number of SIP redirect message is recorded every 30 min and reset to 0. In the example below i am using EIGRP Hello messages for testing. event manager environment _email_server 10.1.1.1 event manager environment _email_to…

Read More
Posted in EEM

Cisco TCL script base commands

Posted on by Admin

Run script !define where the scripts will be stored event manager directory user policy flash: OR event manager directory user policy flash:/eempolicy/ load script copy tftp://10.64.1.2/rtpstreams.tcl flash: Register script event manager policy rtpstreams.tcl when change made them after you reload the script you need to re-register it is well no event manager policy rtpstreams.tcl event manager policy rtpstreams.tcl Run it tcls flash:sipcount.tcl OR tcls source flash:sipcount.tcl debug debug event manager detector ? !turn on debug…

Read More

Dedug SIP trunk from CM to CUBE

Posted on by Admin

Dedug SIP trunk from CM to CUBE   From TAC The link below outlines how to enable detailed traces on CUCM cluster and collect them: Set Up Cisco CallManager Traces for Cisco Technical Support:http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a0080094e89.shtml Now this is the best bit of code i have seen in a long time! Enable SIP debugs, stores them in a txt file on the flash and when the error condition “503 Service Unavailable” happens do some show cmd and…

Read More

Cisco Voice Gateway Commands mostly used

Posted on by Admin

Cisco Voice Gateway Commands mostly used:   Tracing a call flow sh isdn active !overview of calls going through the ISDN sh isdn service !overview of channels used within ISDN interface sh isdn status sh voice call status !gives called, codec and dial-peer info sh dial-peer voice summ !ports, coded, call setup state sh call leg active summary !codec, call type, dial-peer, ip address sh call active voice brief !overview of call leg numbers and…

Read More
Posted in CME

Skype connect with Cisco Cube Config Template

Posted on by Admin

Skype connect with Cisco Cube   ip domain name corp.XXXX.org ip name-server 8.8.8.8 ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip redirect ip2ip fax protocol none no fax-relay sg3-to-g3 h323 sip bind control source-interface Loopback0 bind media source-interface Loopback0 registrar server redirect contact order best-match ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g729r8 ! dial-peer voice 1014 voip…

Read More

CME SRST Template 1

Posted on by Admin

CME SRST Template 1 If 9 for outside line is been removed on CUCM then need to add TP on GW to remove it in SRST Mode voice translation-rule 50 rule 1 /^9\([2-8]…..$\)/ /\1/ rule 2 /^9\(0[12]………\)/ /\1/ rule 3 /^9\(07………\)/ /\1/ rule 4 /^9\(00\)/ /\1/ rule 5 /^9\(0800\)/ /\1/ rule 6 /^\([578]…$\)/ /++44123333\1/ voice translation-profile FailoverOperator translate called 50 Internal range is either 5XXX 7XXX 8XXX and E164 reg phone are +44123333[578]XXX voice translation-rule…

Read More

Cisco VCS root Password Reset/Recovery

Posted on by Admin

This is based on X7.2 software, assuming your software is older but should be the same. To collect logs or other information when there are network problems or other issue preventing access to the Cisco VCS/Conductor remotely, a serial console may be used. Connection should be made to the data port on the front of the appliance. The settings below should be used for the console connection: Setting Value Baud rate 115200 bits per second…

Read More
Posted in VCS

My CUCM SRND Design Notes 10.X – SIP TRUNK Deployments

Posted on by Admin

Best Effort Early Offer [Early Offer support for voice and video calls Best Effort (no MTP inserted)] Best Effort Early Offer can be enabled on the SIP Profile associated with the SIP trunk, and it is the recommended configuration for all Unified CM and Unified CM Session Management Edition (SME) trunks. Best Effort Early Offer trunks never use MTPs to create an Early Offer and, depending on the calling device, may initiate an outbound SIP…

Read More

Unique RD per PE in MPLS VPN for Load Sharing and Faster Convergence

Posted on by Admin

Hi Guys , I found the below link useful for Designing MPLS load sharing and Fast Convergence. Original Link# http://lostintransit.se/2015/01/11/unique-rd-per-pe-in-mpls-vpn-for-load-sharing-and-faster-convergence/   This post describes how load sharing and faster convergence in MPLS VPNs is possible by using an unique RD per VRF per PE. It assumes you are already familiar with MPLS but here is a quick recap. The Route Distinguisher (RD) is used in MPLS VPNs to create unique routes. With IPv4, an IP…

Read More

Cisco IOS- IP Helper Address Command

Posted on by Admin

Original Link# http://www.ciscopress.com/articles/article.asp?p=330807&seqNum=9 Helper Addresses This section describes how networks and routers use helper addresses to forward broadcasts to another server or router on another network. This section describes some of the purposes of and scenarios in which to use helper addresses. Using Helper Addresses DHCP is not the only critical service that uses broadcasts. Cisco routers and other devices might use broadcasts to locate TFTP servers. Some clients might need to broadcast to locate…

Read More
1 … 3,886 3,887 3,888 3,889 3,890 … 3,901