Author: Admin

Cisco 7609 (ROMMON Upgrade Procedure Guide)

Posted on by Admin
Cisco 7609 (ROMMON Upgrade Procedure Guide)

  Verification and backup commands before upgrade:  ! show redundancy!show rom-monitor slot 5 sp show rom-monitor slot 5 rp show rom-monitor slot 6 sp show rom-monitor slot 6 rp show tac !             First start ROMMON upgrade with standby supervisor:                 Note: standby supervisor is in module 6: Please note first upgrade the SP image on standby supervisor and verify after that you can upgrade RP         image on standby…

Read More

Transfered CAlls – CDR Reading

Posted on by Admin

CDR Reading for Transferred Calls Transferred Calls Calls that are transferred generate multiple CDRs. One CDR exists for the original call, one for the consultation call, and another for the final transferred call. For the original call, the origCause_value and destCause_value gets set to split = 393216, which indicates the call was split. The origCallTerminationOnBehalfOf and destCallTerminationOnBehalfOf fields get set to Transfer = 10 to indicate that this call was involved in a transfer. For…

Read More

Cisco PGW Basics

Posted on by Admin

  To manually start the Cisco PGW 2200 Softswitch software, log in to the active Cisco PGW 2200 Softswitch as root and enter the following command: # /etc/init.d/CiscoMGC start To manually stop the Cisco PGW 2200 Softswitch software, log into your active Cisco PGW 2200 Softswitch as root and enter the following command: # /etc/init.d/CiscoMGC stop Starting an MML Session When a procedure requires that you start an MML session, you must perform the following…

Read More

Configuring the Unity Connection 10.x Cluster

Posted on by Admin

Configuring the Unity Connection 10.x Cluster You configure the cluster after you have installed the publisher server. Do the two procedures in this section in the order listed. NoteThe Cisco Unity Connection cluster feature is not supported for use with Cisco Unified Communications Manager Business Edition 3000 and Cisco Unified Communications Manager Business Edition 5000. To Configure the Cisco Unity Connection 10.x Cluster Step 1 On the publisher server, sign in to Cisco Unity Connection…

Read More

How a Cluster Works in Unity Connection 10.x

Posted on by Admin

How a Cluster Works in Unity Connection 10.x The Unity Connection cluster feature provides high availability voice messaging through two Unity Connection servers that are configured in a cluster. Under normal conditions, the Unity Connection servers are both active so that: The cluster can be assigned a DNS name that is shared by the Unity Connection servers. Clients such as email applications and the web tools available through the Cisco Personal Communications Assistant (PCA) can…

Read More

Blocking Inbound calls to Cisco Unified Communications Manager based on Caller ID

Posted on by Admin

  Blocking Inbound calls to Cisco Unified Communications Manager based on Caller ID Introduction: The ability to block calls based on the calling party number is a feature required by many customers to prevent unwanted calls, whether from telemarketer, malicious callers, or others, from reaching their end users. This application note will describe and illustrate how to set up call blocking using Cisco Unified Communications Manager v8.0 and later. Audience: This document is targeted at…

Read More

802.11ac Wireless Packet Captures

Posted on by Admin

In this post we will see how to capture 802.11ac wireless frames using Cisco AP (802.11ac AP like 3700/2700/1700) as remote adapter. I have used OmniPeek WiFi Analyzer (10-day trial version) as protocol analyzer (as Wireshark is not yet support 802.11ac frame analysis). I have installed OmniPeek on my PC (IP x.x.13.20). I have created an Open SSID on my WLC (5508) to connect iPhone6 (single spatial stream 802.11ac client). Also a wired 7965-VoIP connected…

Read More

Lightweight to Autonomous (vice versa) Conversion…

Posted on by Admin

Before converting LWAP to Autonomous need to understand the type of OS image running on these platforms. I found following blog post is very useful to summarize the type of IOS & understanding its naming convention. http://www.my80211.com/cisco-auton-labs/2011/11/19/understanding-cisco-access-point-ios-images.html Following are the three type of IOS available & need to download the correct type before starting the conversion process. k9w7 – autonomous IOS k9w8 – full lightweight IOS (this is what is bundled in the WLC .aes…

Read More

CAPWAP Controller Discovery Process

Posted on by Admin

CAPWAP Controller Discovery Process In a controller-based architecture, CAPWAP access points are dependent on a wireless controller to provide the software image, configuration, and centralized control and optionally data forwarding functions. Therefore, it is necessary for the access point to find a list of available controllers with which it can associate.   The following layer 3 CAPWAP discovery options are supported: Broadcast on the local subnet Local NVRAM list of the previously joined controller, previous…

Read More
1 … 4,043 4,044 4,045 4,046 4,047 … 4,053