How a Cluster Works in Unity Connection 10.x

Posted on by Admin

How a Cluster Works in Unity Connection 10.x The Unity Connection cluster feature provides high availability voice messaging through two Unity Connection servers that are configured in a cluster. Under normal conditions, the Unity Connection servers are both active so that: The cluster can be assigned a DNS name that is shared by the Unity Connection servers. Clients such as email applications and the web tools available through the Cisco Personal Communications Assistant (PCA) can…

Read More

Blocking Inbound calls to Cisco Unified Communications Manager based on Caller ID

Posted on by Admin

  Blocking Inbound calls to Cisco Unified Communications Manager based on Caller ID Introduction: The ability to block calls based on the calling party number is a feature required by many customers to prevent unwanted calls, whether from telemarketer, malicious callers, or others, from reaching their end users. This application note will describe and illustrate how to set up call blocking using Cisco Unified Communications Manager v8.0 and later. Audience: This document is targeted at…

Read More

802.11ac Wireless Packet Captures

Posted on by Admin

In this post we will see how to capture 802.11ac wireless frames using Cisco AP (802.11ac AP like 3700/2700/1700) as remote adapter. I have used OmniPeek WiFi Analyzer (10-day trial version) as protocol analyzer (as Wireshark is not yet support 802.11ac frame analysis). I have installed OmniPeek on my PC (IP x.x.13.20). I have created an Open SSID on my WLC (5508) to connect iPhone6 (single spatial stream 802.11ac client). Also a wired 7965-VoIP connected…

Read More

Lightweight to Autonomous (vice versa) Conversion…

Posted on by Admin

Before converting LWAP to Autonomous need to understand the type of OS image running on these platforms. I found following blog post is very useful to summarize the type of IOS & understanding its naming convention. http://www.my80211.com/cisco-auton-labs/2011/11/19/understanding-cisco-access-point-ios-images.html Following are the three type of IOS available & need to download the correct type before starting the conversion process. k9w7 – autonomous IOS k9w8 – full lightweight IOS (this is what is bundled in the WLC .aes…

Read More

CAPWAP Controller Discovery Process

Posted on by Admin

CAPWAP Controller Discovery Process In a controller-based architecture, CAPWAP access points are dependent on a wireless controller to provide the software image, configuration, and centralized control and optionally data forwarding functions. Therefore, it is necessary for the access point to find a list of available controllers with which it can associate.   The following layer 3 CAPWAP discovery options are supported: Broadcast on the local subnet Local NVRAM list of the previously joined controller, previous…

Read More

WLC Discovery via Broadcast

Posted on by Admin

WLC Discovery via Broadcast original link # http://mrncciew.com/2013/05/04/wlc-discovery-via-broadcast/ As outlined in one of my previous post (AP Registration) there are multiple methods (Broadcast, Static configs, DHCP option 43, DNS) available for a Ligthweight Access Point (LAP) to discover a WLC. In this post we will see how broadcast mechanism can be used for this. After the LAP gets an IP address from the DHCP server, the LAP broadcasts a Layer 3 CAPWAP discovery message on to…

Read More

Cisco Nexus 1000v In Less Than 10 Minutes

Posted on by Admin

original Post #  http://kendrickcoleman.com/index.php/Tech-Blog/standing-up-the-cisco-nexus-1000v-in-less-than-10-minutes.html A few weeks ago at geek week, I was assigned the task of getting the Cisco Nexus 1000v distributed virtual switch set up. I probably spent a good 4 hours on my first cluster because I had no clue what was going on and I ended up losing my management network and spent lots of time restoring my network to the original vSwitch. I followed TrainSignal’s 1000v Installation training in Pro…

Read More

Cisco Nexus 1000v switch – Part 1

Posted on by Admin

This 3 part tutorial guide will show you how to install the Cisco Nexus 1000v switch. I’m will be using this image for the install – Nexus1000v.4.2.1.SV1.4.zip which can be downloaded from the Cisco website. The lab setup is as follows: 1 x ESX 4.1, 1 x ESXi 4.1, vCenter Server and Domain Controller. This Cisco Nexus 1000v requires 3 mandatory virtual machine port groups to be setup in vCenter before installing. Control, Packet and…

Read More

Cisco Nexus 1000v Switch Part 2

Posted on by Admin

  Cisco Nexus 1000v Switch Part 2 1. Now that you have your Cisco Nexus 1000v virtual machine installed, go ahead and power it up. Once it’s powered up, from your management station, open your web browser and browse to the management ip address of your Nexus 1000v that you set in part 1. 2. Click on Launch Installer Application. As a side note, this management station must have Java installed to run the application…

Read More

Cisco Nexus 1000v installation – Part 3

Posted on by Admin

This is part 3 of the Cisco Nexus 1000v installation tutorials.  1. Let’s log into the Nexus 1000v console and type show module. Here you can see that the Virtual Supervisor Module is active and that the ip address is 192.168.1.80. 2. The first thing we need to do is configure our vlans. 3. Now we need to create a port-profile. This port profile is of type ethernet which means that it is assigned to…

Read More
1 … 4,170 4,171 4,172 4,173 4,174 … 4,180